Jonsered CS 2255 Instrukcja Użytkownika

English CS 2255 Operator’ s manual (EPA III) Please read the oper ator’s manual carefully and make sure you understand the instructions before usi

GENERAL SAFETY PRECAUTIONS10 – Englishchain saw, including the cutting equipment, is insulated from the handles by vibration damping units.Cutting har

GENERAL SAFETY PRECAUTIONSEnglish – 11• Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased w

GENERAL SAFETY PRECAUTIONS12 – EnglishSharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth• Never us

GENERAL SAFETY PRECAUTIONSEnglish – 13General advice on adjusting depth gauge setting• When you sharpen the cutting tooth (A) the depth gauge setting

GENERAL SAFETY PRECAUTIONS14 – EnglishLubricating cutting equipmentChain oilChain oil must demonstrate good adhesion to the chain and also maintain it

GENERAL SAFETY PRECAUTIONSEnglish – 15Chain drive sprocketThe clutch drum is fitted with one of the following drive sprockets:A Spur sprocket (the ch

ASSEMBLY16 – EnglishFitting the bar and chainCS 2255Check that the chain brake is in disengaged position by moving the front hand guard towards the fr

ASSEMBLYEnglish – 17Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the g

FUEL HANDLING18 – EnglishFuelNote! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke

FUEL HANDLINGEnglish – 19FuelingClean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at l

KEY T O SYMBOLS 2 – English Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fat

STARTING AND STOPPING20 – EnglishStarting and stoppingStarting: The chain brake should be activated when starting the chain saw. Activate the chain br

STARTING AND STOPPINGEnglish – 21unnecessary wear to the clutch, clutch drum and brake band.Allow the machine to idle a few seconds before giving full

WORKING TECHNIQUES22 – EnglishBefore use:1 Check that the chain brake works correctly and is not damaged.2 Check that the rear right hand guard is not

WORKING TECHNIQUESEnglish – 236 Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with

WORKING TECHNIQUES24 – Englishuser. If the saw chain is jamming, the saw may be pushed back at you.8 Unless the user resists this pushing force there

WORKING TECHNIQUESEnglish – 25LimbingWhen limbing thick branches you should use the same approach as for cutting.Cut difficult branches piece by piece.

WORKING TECHNIQUES26 – EnglishTree felling techniqueSafe distanceThe safe distance between a tree that is to be felled and anyone else working nearby

WORKING TECHNIQUESEnglish – 27FellingFelling is done using three cuts. First you make the directional cuts, which consist of the top cut and the botto

WORKING TECHNIQUES28 – EnglishWe recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and d

WORKING TECHNIQUESEnglish – 29How to avoid kickbackWhat is kickback?The word kickback is used to describe the sudden reaction that causes the chain sa

CONTENTS English – 3 Contents KEY TO SYMBOLS Symbols on the machine: ... 2Symbols in the operator’s manual: .

MAINTENANCE30 – EnglishGeneralThe user must only carry out the maintenance and service work described in this manual. More extensive work must be carr

MAINTENANCEEnglish – 31The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits th

MAINTENANCE32 – EnglishChecking the brake triggerPlace the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any

MAINTENANCEEnglish – 33Right hand guardCheck that the right hand guard is not damaged and that there are no visible defects, such as cracks.Vibration

MAINTENANCE34 – EnglishStarterChanging a broken or worn starter cord• Loosen the screws that hold the starter against the crankcase and remove the sta

MAINTENANCEEnglish – 35Changing a broken recoil spring• Lift up the starter pulley. See instructions under the heading Changing a broken or worn start

MAINTENANCE36 – EnglishSpark plugThe spark plug condition is influenced by:• Incorrect carburetor adjustment.• An incorrect fuel mixture (too much or i

MAINTENANCEEnglish – 37Cooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst

38 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 39TECHNICAL DATATechnical dataCS 2255EngineCylinder displacement, cu.in/cm33,38/55,5Cylinder bore, inch/mm 1,85/47Stroke, inch/mm 1,26/32,0I

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

40 – EnglishTECHNICAL DATARecommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the

FEDERAL EMISSION CONTROL WARRANTY STATEMENTEnglish – 41YOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

´®z+SFQ¶53¨´®z+SFQ¶53¨42 – EnglishAMERICAN STANDARD SAFETY PRECAUTIONSSafety precautions for chain saw users(ANSI B175.1-2000 Annex C)Kickback safety

1151384-95´®z+SFQ¶53¨´®z+SFQ¶53¨2008-12-19

English – 5 WHA T IS WHA T? What is what on the c hain saw?313648971112105113171914151627262423222118202525 28 2932302 1 Information and warning d

GENERAL SAFETY PRECA UTIONS 6 – English Bef ore using a new chain saw • Please read this manual carefully.• Check that the cutting equipment is cor

GENERAL SAFETY PRECA UTIONS English – 7 Al ways use common sense It is not possib le to cover every conceivable situation you can face when using

GENERAL SAFETY PRECAUTIONS8 – English• The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia releas

GENERAL SAFETY PRECAUTIONSEnglish – 9of the front hand guard, the chain brake can only be activated by the inertia action. Will my hand always activa