Jonsered CS 2156 Instrukcja Operatora

CS 2156 CS 2159 Operator’s manual (EPA) Please read the operator’s manual carefully and make sure you understand the instructions before using the m

10 – English SAFETY INSTRUCTIONS Vibration damping system Regularly check the vibration damping units for cracks or deformation.Make sure the vibrat

English – 11 SAFETY INSTRUCTIONS Cutting equipment designed to minimise kickback The only way to avoid kickback is to make sure that the kickback zo

12 – EnglishSAFETY INSTRUCTIONS• Level of kickback reduction. The level of kickback reduction offered by a chain is only indicated by its model number

English – 13SAFETY INSTRUCTIONS• Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one si

14 – EnglishSAFETY INSTRUCTIONS• Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you

English – 15SAFETY INSTRUCTIONSNeedle bearing lubricationThe clutch drum is fitted with one of the following drive sprockets:A Spur sprocket (the cha

16 – EnglishSAFETY INSTRUCTIONSHow to avoid kickbackWhat is kickback?The word kickback is used to describe the sudden reaction that causes the chain s

English – 17SAFETY INSTRUCTIONSUnless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the

18 – EnglishSAFETY INSTRUCTIONSobjects. Then grasp the starter handle with your right hand and pull the starter cord. Never wrap the starter cord arou

English – 19SAFETY INSTRUCTIONS• Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, di

2 – English KEY TO SYMBOLS Key to symbols WARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to t

20 – EnglishSAFETY INSTRUCTIONSIn most cases you can avoid these problems by cutting in two stages; from the top and from the bottom. You need to supp

English – 21SAFETY INSTRUCTIONSTree felling techniqueSafe distanceThe safe distance between a tree that is to be felled and anyone else working nearby

22 – EnglishSAFETY INSTRUCTIONSThe directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut

English – 23SAFETY INSTRUCTIONSLimbingMake sure that you can stand and move about safely. Work on the left side of the trunk. Work as close as possibl

24 – EnglishWHAT IS WHAT?What is what on the chain saw?1 Cylinder cover2 Front handle3 Front hand guard4 Starter5 Chain oil tank6 Starter handle7 Adju

English – 25ASSEMBLYFitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han

26 – EnglishFUEL HANDLINGFuelCAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-st

English – 27FUEL HANDLINGChain oil• The chain lubrication system is automatic and we recommend the use of special oil (chain oil) with good adhesion c

28 – EnglishSTARTING AND STOPPINGStarting and stoppingCold engineStarting: The chain brake should be activated when starting the chain saw. Activate t

English – 29STARTING AND STOPPINGPull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use.Stop

English – 3 CONTENTS Contents Before using a new chain saw • Please read the operator’s manual carefully and make sure you understand the instructio

30 – EnglishMAINTENANCECarburettorYour Jonsered product has been designed and manufactured to specifications that reduce harmful emissions.After your u

English – 31MAINTENANCEuntil the engine runs smoothly. The high speed needle H is correctly set when the saw “4-cycles” a little. If the machine “whis

32 – EnglishMAINTENANCEFitting the starter• To fit the starter, first pull out the starter cord and place the starter in position against the crankcase.

English – 33MAINTENANCENeedle bearing lubricationThe clutch drum is fitted with one of the following drive sprockets:A Spur sprocket (the chain sproc

34 – EnglishMAINTENANCEHeated handles (CS 2156W, CS 2159W)On models with the model code W, both the front handle bar and the rear handle are equipped

English – 35MAINTENANCEBelow you will find some general maintenance instructions.Daily maintenance1 Check the throttle trigger for smooth operation. If

36 – EnglishTECHNICAL DATATechnical dataCS 2156 CS 2159EngineCylinder volume, cu.in/cm33,45/56,5 3,60/59,0Cylinder bore, inch/mm 1,81/46 1,85/47Str

English – 37TECHNICAL DATARecommended original and replacement bar and chain combinationsFollowing is a list of recommended cutting equipment for the

38 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENT´®z*xy3¶5A¨´®z*xy3¶5A¨YOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protect

´®z*xy3¶5A¨2003-10-23´®z*xy3¶5A¨1088891-95

4 – English CONTENTS You will find the following labels on your machine: EPA IEPA II The Emissions Compliance Period referred to on the Emission Comp

English – 5 SAFETY INSTRUCTIONS Personal protective equipment • Protective helmet• Hearing protection• Protective goggles or a visor• Gloves with sa

6 – English SAFETY INSTRUCTIONS Chain brake and front hand guard Your chain saw is equipped with a chain brake that is designed to stop the chain im

English – 7 SAFETY INSTRUCTIONS it cannot affect the movement of the front hand guard, the chain brake can only be activated by the inertia of the c

8 – English SAFETY INSTRUCTIONS Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.In ar

English – 9 SAFETY INSTRUCTIONS Checking the inertia brake release Hold the chain saw over a stump or other firm object. Let go of the front handle s